Irrigation Stakes


You are here: Home -> Products -> Irrigation Stakes
Global Irrigation, Inc. specializes in carrying a good selection of Irrigation Stakes that are commonly used in drip irrigation systems. From all-purpose holding stakes that are used to hold several sizes of micro-tubings in place to stakes that are used to elevate the height of sprinklers or sprayers, we have them all. For further product inquiry, please contact us. We will be glad to assist you further.
  • Micro Irrigation Stakes - 2016
    2016 : Micro Irrigation Stakes
    6" Micro Tubing Holding Stake

    • 6" Holding Stake fits 0.125, 0.185, 0.200, 0.250 and 0.307 Micro Tubing, and holds the tubing in place.
    • The 2016 Micro Tubing Holding Stake elevates drip emitters, sprayers, and micro tubing above the ground. It prevents dirt clogging to the emission devices and keeps bugs and dirt out of the tubing.
    • To use, simply place micro tubing into the V notch, and push down the stake into the ground.
    • The 2016 Micro Tubing Holding Stake is a versatile stake and can be used near plants, in flower pots, and garden boxes.
  • Drip Irrigation Stakes - 2010
    2010 : Drip Irrigation Stakes
    12" Press-Fit Stake

    • 12" Stake to raise up Press-fit Sprayers/sprinklers above the ground.
    • A replacement stake for press-fit support assembly.
    • Enlarged hole on the stake allows ¼" tubing assemblies to go through easier.
    • Improved press-fit connector is now more versatile to fit different press-fit sprinklers.
  • Micro Stakes - 2012
    2012 : Micro Stakes
    • 12" Clip Stake
    • Rigid Risers or ¼ tubing could be pushed into the Clip of the stake.
    • 12" Clip Stake is used to extend micro sprinklers or mini sprayers, on rigid risers or with 1/4" tubing, above the plant area.
    • Prevents tripping hazards and damage to drip system.
    • The flat top could be hammered into the soil if needed.
    • Close up image as above.
  • Spray Stake - 2014
    2014 : Spray Stake
    • 12" Stake with #10-32 Thread Inlet and 1/4" Barbed Outlet.
    • Global 2014 Stake is used to elevate a micro sprinkler/ sprayer and secure it in position.
    • Thread in the mini sprinkler/ sprayer with #10-32 thread to the top hole of this stake.
    • The Barbed Outlet is used to connect 1/4" flexible vinyl tubing (.152"-.160"/ 3.86mm-4.07mm ID) or with 1/4" poly tubing (.157"-.165"/ 4.0mm-4.2mm ID ).
    • Ideal for horticultural application, flower beds, and large areas of plantation in landscaped areas.
    • New enlarged hole on the stake makes ¼" tubing assembly go through easier.
    • Close up image as above.
  • Micro Sprinkler Stakes - 2038
    2038 : Micro Sprinkler Stakes
    12" Stake with 3/8” FPT Outlet x 1/4” Barbed Inlet

    • 12" Stake with 3/8" Female Pipe Thread Taper Outlet x 1/4" Barbed Inlet for 1/4" flexible vinyl Tubing with 0.270" OD (ID .156"-.164"/ 3.96mm-4.17mm) or 1/4" Poly tubing with ID .193"-.200"/ 4.9mm-5.1mm.
    • Thread in mini sprinklers with 3/8" Male Pipe Thread (our part no. 7436 series) to the outlet of 2038 stake.
    • A straight 1/4" barbed inlet accepts 1/4" poly and/or flexible vinyl tubing.
    • Widely used for landscape and Orchard irrigation.
    • This 2038 stake assembly includes press-fit stake (our part no. 2010) and press-fit bridge with 3/8" Female Pipe Thread Taper x 1/4" Barb (our part no. 1032).
    • Smaller 1/4" barbed version (our part no. 1032N) is also available upon request.
    • 2038N stake assembly fits 1/4" flexible vinyl tubing with .245 OD (ID .152"-.160"/ 3.86mm-4.07mm) or 1/4" poly tubing with ID .157"-.165"/ 4.0mm-4.2mm.
  • Stake Connectors - 1032N
    1032N : Stake Connectors
    Press-fit bridge for 3/8" Female Pipe Thread Taper With 1/4" Barb Inlet

    • Press-fit connector with 3/8" Female Pipe Thread Taper and smaller 1/4" Barb for 1/4" flexible vinyl Tubing with 0.245" OD (ID .152"-.160"/ 3.86mm-4.07mm) or 1/4" poly tubing with .157"-.165"/ 4.0mm-4.2mm ID.
    • Assemble 1032N Press-fit Bridge with press-fit stake (our part no. 1020) to make a stake with 3/8" Female Pipe Thread Outlet x 1/4" Barb Inlet (our part no 2038N).
    • 1032N is used to connect mini sprinklers with 3/8" Male Pipe Thread (our part no. 7436 series) and 1/4" micro tubing.
    • Larger 1/4" barbed Press-fit Bridge (our part no. 1032) is also available upon request. 1032 fits 1/4" flexible vinyl Tubing with 0.270" OD (ID .156"-.164"/ 3.96mm-4.17mm) or 1/4" Poly tubing with ID .193"-.200"/ 4.9mm-5.1mm.
  • Drip Stakes - AS-06H
    AS-06H : Drip Stakes
    6" Elbow Stake

    • 6" Elbow Stake with 1/4" Barb side Inlet x #10-32 Thread Outlet and Protective Hood.
    • The threaded top accepts a short length of 1/4" tubing or Rigid Riser between the stake and the sprayer. Barb on the side accepts 1/4" tubing from the mainline.
    • The Protective Hood gives extra support to the rigid riser setup.
    • Ideal to elevate rigid riser and micro sprayer above the planted area to accommodate various application needs.
    • Global Elbow Stake can be assembled with 4 lengths of rigid risers upon request. RR6-6 (6" rigid riser on the 6" elbow stake), RR8-6 (8" rigid riser on the 6" elbow stake), RR12-6 (12" rigid riser on the 6" elbow stake), RR18-6 (18" rigid riser on the 6" elbow stake).
  • Adjustable Stakes - AS-08HV
    AS-08HV : Adjustable Stakes
    8" Elbow Stake with Adjustable Valve

    • Global 8" Elbow Stake with Adjustable Valve, with 1/4" Barb side Inlet and #10-32 Thread Outlet.
    • AS-08HV has a built-in control valve to easily adjust the flow and distance of spray from a Micro Jet Sprayer or any other sprayer.
    • The control valve allows complete shut-off operation.
    • The Protective Hood surround the #10-32 threaded outlet provides extra protection to the rigid riser.
    • The Barb on the side of the stake connects 1/4" tubing from the mainline.
    • AS-08HV also has a convenient Hole Punch on the stake for immediately use to connect ¼" tubing from mainline.
    • Global Elbow Stake can be assembled with 4 lengths of rigid risers upon request. RR6-8 (6" rigid riser on the 8" elbow stake), RR8-8 (8" rigid riser on the 8" elbow stake), RR12-8 (12" rigid riser on the 8" elbow stake), RR18-8 (18" rigid riser on the 8" elbow stake).
  • Pipe Stakes - 2017
    2017 : Pipe Stakes
    1/2" Tubing Hold Down Stake

    • 13mm (5 in) Tubing Stake for hold .600, .700, .710 OD Tubing (14mm-18mm) in place.
    • 2017 Hold Down Stake is used to hold polyethylene tubing in place from tripping hazards or damaging the drip system.
    • To install, just place the hold-down next to the tubing and push it down to the soil to neatly secure the tubing in place.
    • This hold-down stake could also be hammered into the ground.
    • This economic accessory ensures a clean finish for the installation of irrigation system.
We carry various types of

Irrigation Stakes

that can be used in almost every irrigation system environment. We also pride ourselves on same-day shipping to ensure on-time delivery.
Italian, Italiano